Search:

Type: Posts; User: jerm8352

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Sticky: Thank you!

    Thank you!
  2. Replies
    2
    Views
    102

    Yeah, coyote and prairie dog would be the only...

    Yeah, coyote and prairie dog would be the only thing I would hunt with this. But I do want something decent.
  3. Replies
    38
    Views
    1,361

    Thanks for all the help. This is a hard thing to...

    Thanks for all the help. This is a hard thing to start, but very rewarding!
  4. Replies
    2
    Views
    102

    Reflex red dot sight

    Hey guys, bought my first ar 15 recently and I am looking for a cheaper ($100ish) red dot sight. I know you get what you pay for with optics, but i really just want it for plinking so I do not want...
  5. Replies
    8
    Views
    214

    Well.... I am an idiot. I must have forgotten to...

    Well.... I am an idiot. I must have forgotten to chamfer and deburr the case mouths because after doing that they work fine. I did already have about 15 round that I really, had to apply pressure...
  6. Replies
    8
    Views
    214

    The case lengths are consistent and it is tight...

    The case lengths are consistent and it is tight all the way. Almost like the bullet is getting stuck in the die but only with the 180s. I backed the die out quite a bit but it didn't help. Thanks...
  7. Replies
    8
    Views
    214

    300 win mag bullet seater problem

    Hello again guys. Time for the reloading newbie to beg for more help.

    Anyways, I have been trying to reload 300 win mag now. When I try to seat the bullet, I am getting ALOT of resistance, and...
  8. Replies
    38
    Views
    1,361

    I have the Hornady reloading manual as well and...

    I have the Hornady reloading manual as well and am looking to get the nosler one too as I use their bullets a lot. I also have a caliper.
    Thanks for all the help.
  9. Replies
    38
    Views
    1,361

    I readjusted the seating die and ran some dummy...

    I readjusted the seating die and ran some dummy rounds and these seemed to be much better. I put the already loaded rounds through the seating die again and they seemed to be much better. I will...
  10. Replies
    30
    Views
    1,238

    The slide was the problem with my wife. I have a...

    The slide was the problem with my wife. I have a little sig sauer 380 that she liked shooting but she could not operate the slide efficiently. So, that was a great reason to have to buy another gun.
  11. Replies
    30
    Views
    1,238

    I hate typing on an ipad. Stupid autocorrect!

    I hate typing on an ipad. Stupid autocorrect!
  12. Replies
    30
    Views
    1,238

    Yeah I do, I have not shot any through it or had...

    Yeah I do, I have not shot any through it or had her yet. But I am sure we will.
  13. Replies
    30
    Views
    1,238

    I do not want to change her. If it works for...

    I do not want to change her. If it works for her, I am ok with it.
  14. Replies
    30
    Views
    1,238

    My wife shoots a ruger lcr in 38 special. I hate...

    My wife shoots a ruger lcr in 38 special. I hate it but she loves it.
  15. Replies
    38
    Views
    1,361

    I did deburr the brass. I will turn the bullet...

    I did deburr the brass. I will turn the bullet seating die down a little bit, run the batch through and see what happens. Thanks so much.
  16. Replies
    38
    Views
    1,361

    Thanks everyone for the help. I will check out...

    Thanks everyone for the help. I will check out all this stuff later this week. This is a fun but tough thing to start doing without having someone around to show you the ropes.

    The dies and...
  17. Replies
    38
    Views
    1,361

    No, its both, thats why I am so confused

    No, its both, thats why I am so confused
  18. Replies
    38
    Views
    1,361

    I do not see any visible marks but I will check...

    I do not see any visible marks but I will check again. I am loading 30-06 rounds using federal brass and 180 grain nosler partitions and ballistic silvertips. Thank you all so much
  19. Replies
    38
    Views
    1,361

    I checked the col and it is fine. All the cases...

    I checked the col and it is fine. All the cases were trimmed to the "trim to length" specified in the lyman reloading handbook. Still not sure on the problem. Do I just shoot all the trimmed cases...
  20. Replies
    38
    Views
    1,361

    Sorry about leaving out info. The cartridges are...

    Sorry about leaving out info. The cartridges are all the same brand and all have only been shot in my rifle. I shot them once, full length resized them. (Probably shouldnt have done that but I am...
  21. Replies
    38
    Views
    1,361

    Rifle reloading questions

    Hey, i have a couple of rifle reloading questions.

    I recently reloaded a batch of 30-06 cartridges. I have reloaded this caliber and bullet combo before with no problems before. However, this...
  22. Replies
    16
    Views
    580

    Nope, im doing it just as you described

    Nope, im doing it just as you described
  23. Replies
    16
    Views
    580

    Thats what I thought but it just sounded weird in...

    Thats what I thought but it just sounded weird in my head. Thanks again!
  24. Replies
    16
    Views
    580

    Recycle as in use the powder again? I wondered...

    Recycle as in use the powder again? I wondered if the short case was part of the problem. Thank you very much again!
  25. Replies
    16
    Views
    580

    So I tried the rcbs hammer puller again today...

    So I tried the rcbs hammer puller again today with similar results. I tightened the end as best as I could before every swing and when the bullet would come out I could see powder shooting up...
Results 1 to 25 of 47
Page 1 of 2 1 2