Results 1 to 9 of 9

Hybrid View

  1. #1
    Junior Member
    Join Date
    Sep 2012
    Location
    sutter,ca.
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Congratulations
    0
    Congratulated 0 Times in 0 Posts

    Question for the experts?

    I have a weatherby mark v ultra light in 300 weatherby mag and in the last few sessions at the range i have had a problem with my bolt being stuck down after the shot. Not every shot maybe 1 out of 7 shots and at the same time that bullet will be a flier by maybe 5 or 6 inches in no particular direction. Any thoughts or advise?

  2. #2
    Senior Member
    Join Date
    Dec 2011
    Location
    Bitteroots
    Posts
    391
    Thanks
    31
    Thanked 32 Times in 25 Posts
    Congratulations
    0
    Congratulated 40 Times in 2 Posts
    To hot of loads. To high of pressure.

  3. #3
    Super Moderator
    Join Date
    Feb 2011
    Location
    Reno Nv
    Posts
    4,290
    Thanks
    983
    Thanked 582 Times in 415 Posts
    Congratulations
    120
    Congratulated 46 Times in 6 Posts
    Are you reloading your own bullets?

  4. #4
    Junior Member
    Join Date
    Sep 2012
    Location
    sutter,ca.
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Congratulations
    0
    Congratulated 0 Times in 0 Posts
    No factory weatherby ammo, 180 gr partitions?

  5. #5
    Member
    Join Date
    Jul 2012
    Posts
    83
    Thanks
    1
    Thanked 12 Times in 7 Posts
    Congratulations
    0
    Congratulated 0 Times in 0 Posts
    Call Weatherby, just to make sure that they don't have a recall or something. I have seen this in the overpressure ammo, like the "light Magnum" ammo that Hornady puts out. Is it a new rifle?

  6. #6
    Member
    Join Date
    Jul 2011
    Posts
    74
    Thanks
    5
    Thanked 4 Times in 4 Posts
    Congratulations
    0
    Congratulated 0 Times in 0 Posts
    I agree that high pressure is the most likely cause. Is all the ammo from the same lot? Have you ever had issues before? Excess headspace or burrs in the barrel (sometimes from cleaning) are likely culprits. Check your chamber too. I have seen a few with so much oil in them they cause high pressure. Weatherby loads are pretty "hot" pressure-wise to begin with and it doesn't take much to spike pressures above safe limits. At any rate I would not shoot it again until you get it looked at, as strong as Weatherby's are all guns have limits on how many times they can be exposed to overly high pressures. The results of an action coming from together will at best ruin the gun and at worst severely injure the shooter.
    Last edited by Highcountry Dreams; 10-02-2012 at 04:29 PM.

  7. #7
    Junior Member
    Join Date
    Sep 2012
    Location
    sutter,ca.
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Congratulations
    0
    Congratulated 0 Times in 0 Posts
    Thnks for the reply's, I was headed back out tonight if i have another lot number of ammo but sounds like i should get a hold of weatherby before i go to much further. Have a hunt in 10 days hope to get something figured out before then. Thanks again for the help.

  8. #8
    Member
    Join Date
    Jul 2012
    Posts
    83
    Thanks
    1
    Thanked 12 Times in 7 Posts
    Congratulations
    0
    Congratulated 0 Times in 0 Posts
    If you could get a pic of your brass, including a pic of your dented primer?

  9. #9
    Senior Member
    Join Date
    Feb 2011
    Location
    Jim Bridger County, Utah
    Posts
    1,266
    Thanks
    158
    Thanked 240 Times in 182 Posts
    Congratulations
    26
    Congratulated 58 Times in 6 Posts
    To hot of load or headspace issues!
    TICK
    TALL, WIDE and HANDSOME


    "The will to win, the desire to succeed, the urge to reach your full potential... these are the keys that will unlock the door to personal excellence."
    Confucius

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •