Page 1 of 5 123 ... LastLast
Results 1 to 10 of 49
  1. #1
    Senior Member
    Join Date
    Mar 2011
    Location
    Colorado Mountains
    Posts
    588
    Thanks
    28
    Thanked 84 Times in 71 Posts
    Congratulations
    1
    Congratulated 11 Times in 3 Posts

    Muzzleloader bullets/ Thor/No Excuses/PB

    Thor...Finally had a chance to try out the Thor bullets today at the range. I tried both the .502 & .503 in 250 grain. Although I could get the .503 from the sizing pack Thor sends down the barrel at home, I could not get the bullets down today at the range. The .502 goes down pretty stiff but is acceptable. The problem is trying to get a second one down after the barrels fouled. It's really hard to get down even using my "range rod" which is longer, heavier duty, and has a larger T-handle then the ram rod on my gun to use in the field. I'm afraid if I had to make a follow up shot in the field I would have a really hard time getting the bullet down. I'd also be afraid of not getting it seated on the powder well enough. It seemed like my ram rod went down 1/4 to 1/2 inch less on the second shots. I'm assuming because of the fouling building up as you push the bullet down? I'm thinking of trying the .501 instead. I would like to be able to get two shots off, preferably three before having to swab the barrel. Other than the loading issue they seemed to pattern really well. just over a 1" group at 50 yds. using fiber optic sites. That's probably as tight a group as I've ever gotten with any muzzleloader bullet using open sites.

    No Excuses... I tried the 460 grain a few years ago but couldn't remember the results so I ordered some more to try out. Now I know why I didn't use them. These bullets loaded great, nice and smooth even though there .503. I'm sure the pre-lube helps. They were all over the place. I would shoot one, then the next might be 3 inches or 6 inches away. Nothing consistent. Too bad, I like the idea of the big lead conical. I would still like to use these in another gun before writing them off. I know other guy's have had good luck. For the record, I shoot a T/C Omega which I've learned does not like big conicals, which is probably why.

    Powerbelts... I started several years ago with the power belt 295 grain aero tip and have killed a few animals with it including elk. I've never much cared for the bullet and the reports from others haven't been good. Here's what I will say... the powerbelt loaded great with the barrel fouled even after two shots which is a huge bonus. I only shot a few but got just over 2" groups. I only wish they were a better constructed bullet and held up better. The loading is so nice, it makes me want to use them.

    I'll probably be using either the .502 or .501 Thor bullet this year. I still need to try out the .501 first. Need to get some on order so I'm not still trying to get the muzzleloader dialed in while I should be out archery hunting!

  2. #2
    Banned
    Join Date
    Dec 2011
    Location
    Buena Vista, Co.
    Posts
    1,137
    Thanks
    1
    Thanked 52 Times in 38 Posts
    Congratulations
    0
    Congratulated 0 Times in 0 Posts
    What powder are you using? I always used BH 209 with Thors, and could load 50 in a row with no swabbing, and they were a tight fit to start off with. Actually, BH seemed to lube the bore, as it seemed they loaded easier the more I shot.

    T7 on the other hand is a swab every shot. I hate that crap!

  3. #3
    Senior Member
    Join Date
    Mar 2011
    Location
    Colorado Mountains
    Posts
    588
    Thanks
    28
    Thanked 84 Times in 71 Posts
    Congratulations
    1
    Congratulated 11 Times in 3 Posts
    Quote Originally Posted by Old Hunter View Post
    What powder are you using? I always used BH 209 with Thors, and could load 50 in a row with no swabbing, and they were a tight fit to start off with. Actually, BH seemed to lube the bore, as it seemed they loaded easier the more I shot.

    T7 on the other hand is a swab every shot. I hate that crap!
    I'm using T7. Maybe I should try the BH209? Thanks for the tip...

  4. #4
    Banned
    Join Date
    Dec 2011
    Location
    Buena Vista, Co.
    Posts
    1,137
    Thanks
    1
    Thanked 52 Times in 38 Posts
    Congratulations
    0
    Congratulated 0 Times in 0 Posts
    Yeah, T7 leaves a crud ring right above the charge. You won't get that at all with BH 209. Don't be tempted to swab during shooting sessions. It's actually more accurate to not swab at all until you're done shooting.

    Also, in case your don't know. You use the same solvents to clean BH 209 that you do for your CF guns. DON'T use black powder products, water and soap etc to clean BH 209.

    If you haven't already guessed. BH 209 is basically a smokeless powder that's been detuned to black powder power. So, it loads with the same volume loads as T7.

  5. #5
    Member
    Join Date
    Apr 2011
    Location
    Boncarbo Colorado
    Posts
    62
    Thanks
    0
    Thanked 1 Time in 1 Post
    Congratulations
    0
    Congratulated 0 Times in 0 Posts
    With T7, You'll get the nastiest crud ring down at the breech. Make SURE you mark your ramrod on a clean barrel so you have a witness mark. Not seating the bullet all the way can ruin your day in more ways than one. And the biggest one isnt very clean.

    What rifle are you shooting again?

  6. #6
    Senior Member
    Join Date
    Mar 2011
    Location
    Colorado Mountains
    Posts
    588
    Thanks
    28
    Thanked 84 Times in 71 Posts
    Congratulations
    1
    Congratulated 11 Times in 3 Posts
    Quote Originally Posted by FrontierMuzzleloading View Post
    With T7, You'll get the nastiest crud ring down at the breech. Make SURE you mark your ramrod on a clean barrel so you have a witness mark. Not seating the bullet all the way can ruin your day in more ways than one. And the biggest one isnt very clean.

    What rifle are you shooting again?
    T/C Omega .50 cal.

  7. #7
    Banned
    Join Date
    Dec 2011
    Location
    Buena Vista, Co.
    Posts
    1,137
    Thanks
    1
    Thanked 52 Times in 38 Posts
    Congratulations
    0
    Congratulated 0 Times in 0 Posts
    Good! You have the perfect breech plug to shoot BH 209. Just make sure you use shotgun 209 primers, and not the 209 primers made for muzzleloaders. They have a weaker flame to keep the crud ring down with T7. They aren't hot enough to ignite BH 209.

    If they say anything about muzzleloaders on the package of primers. Don't use them.

  8. #8
    Senior Member
    Join Date
    Jul 2011
    Location
    colfax, wa
    Posts
    5,217
    Thanks
    1,280
    Thanked 665 Times in 572 Posts
    Congratulations
    198
    Congratulated 24 Times in 11 Posts
    I used triple 7 fffg and hornady FPB's when I went to CO last. It shot well in my Knight disc extreme.

  9. #9
    Senior Member
    Join Date
    Jul 2013
    Location
    loretto ky
    Posts
    180
    Thanks
    2
    Thanked 15 Times in 14 Posts
    Congratulations
    0
    Congratulated 11 Times in 2 Posts
    I heard they will send you a sample pack of different sizes to fit your gun.

  10. #10
    Banned
    Join Date
    Dec 2011
    Location
    Buena Vista, Co.
    Posts
    1,137
    Thanks
    1
    Thanked 52 Times in 38 Posts
    Congratulations
    0
    Congratulated 0 Times in 0 Posts
    He will. Just e-mail Terry, and he'll send it right out.

 

 

Similar Threads

  1. Woodleigh bullets
    By AKaviator in forum Guns, Muzzleloaders and Ammo
    Replies: 2
    Last Post: 03-30-2014, 03:11 PM
  2. How long will bullets last?
    By Ikeepitcold in forum Guns, Muzzleloaders and Ammo
    Replies: 24
    Last Post: 03-14-2014, 12:57 PM
  3. Thor Bullet shooters - A new helper!
    By FrontierMuzzleloading in forum Guns, Muzzleloaders and Ammo
    Replies: 2
    Last Post: 12-16-2013, 09:22 PM
  4. Thor .50 cal. M/L Bullets- Anyone want some?
    By Colorado Cowboy in forum Guns, Muzzleloaders and Ammo
    Replies: 11
    Last Post: 07-15-2012, 03:06 PM
  5. Colorado Muzzleloader Bullets - 2x diameter?
    By TimG in forum Guns, Muzzleloaders and Ammo
    Replies: 1
    Last Post: 06-24-2011, 01:54 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •