Results 1 to 8 of 8
  1. #1
    Senior Member
    Join Date
    Mar 2013
    Location
    Cleveland, OH area
    Posts
    409
    Thanks
    26
    Thanked 63 Times in 52 Posts
    Congratulations
    6
    Congratulated 0 Times in 0 Posts

    Replacement stock for a remington 788 6mm

    Recently I was given my grandfathers Remington 788. I shot it yesterday and it still shoots great. 15 rounds at 100 yds all in the same 1x1 square!!!!!!

    I hate to risk screwing up a good thing, but the stock on this gun is in pretty bad shape. No cracks, but ugly otherwise. Any recommendations on a replacement stock? I've never been into gun smithing so I'm definitely new when it comes to anything beyond changing a scope out and taking my guns apart to clean them so I'm not even really sure what is good or what isn't. Don't want to spend a lot of money but I'm not sure what a decent stock will cost.

    Thanks for the help.

  2. #2
    Senior Member
    Join Date
    Jul 2011
    Location
    colfax, wa
    Posts
    4,847
    Thanks
    1,099
    Thanked 563 Times in 493 Posts
    Congratulations
    9
    Congratulated 5 Times in 5 Posts
    Not alot available for the 788. I did find these places that have them but you might look into getting your stock refinished or just leave it as it is. The deer you shoot will never know what the stock on the gun you killed him with looked like! HAHA

    http://www.usariflestocks.com/Reming...ck-Tundra.html

    http://www.gun-parts.com/remingtonstocks/

    http://www.gunpartscorp.com/Manufact...tm?results=All
    Last edited by Musket Man; 06-08-2014 at 08:03 AM.
    Keystone 1, Over!

    " I am lost in the dust of the chase that my life brings"

  3. #3
    Senior Member
    Join Date
    Oct 2012
    Location
    Sasakwa, Oklahoma
    Posts
    728
    Thanks
    57
    Thanked 102 Times in 88 Posts
    Congratulations
    0
    Congratulated 0 Times in 0 Posts
    Check out boyds, here is the link. http://www.boydsgunstocks.com/produc...18550&cat=1220

    They start at $99, you might also consider re-finishing the stock you have?
    "Only two people have died for You and I, The American Soldier died for Our Freedom & Jesus Christ Died for Our Souls!" I thank GOD for them! GOD BLESS AMERICA!



    NRA Life Member

  4. #4
    Senior Member
    Join Date
    Dec 2011
    Location
    Carlin, NV
    Posts
    632
    Thanks
    63
    Thanked 88 Times in 85 Posts
    Congratulations
    6
    Congratulated 0 Times in 0 Posts
    I would look into refinishing it either yourself or professionally. Since there is no cracks, when re-done it will look like a whole new stock and depending on the color, the grain of the wood might possibly "pop"!

  5. #5
    Senior Member
    Join Date
    Jun 2011
    Location
    Dolores, Colorado
    Posts
    2,433
    Thanks
    107
    Thanked 350 Times in 271 Posts
    Congratulations
    1
    Congratulated 0 Times in 0 Posts
    I have refinished a ton of stocks, not really to hard to do. PM me if you want details.
    Colorado Cowboy
    Cowboy Action Shooter; Endowment Life Member-NRA
    The Original Rocket Scientist-Retired
    "My Father always considered a walk in the mountains as the equivalent of church going."
    Aldous Huxley

  6. #6
    Senior Member
    Join Date
    Mar 2013
    Location
    Cleveland, OH area
    Posts
    409
    Thanks
    26
    Thanked 63 Times in 52 Posts
    Congratulations
    6
    Congratulated 0 Times in 0 Posts
    I did think of refinishing this stock and I still may. My wife was planning to use this gun and I thought I would try to get her something that she liked with a recoil pad on it vs the metal plate on the stock now.

    I did see Boy'ds had a decent selection among others but are these going to need a lot of fitting once purchased or should they require minor modifications if any?

  7. #7
    Senior Member
    Join Date
    Jun 2011
    Location
    Kingwood, TX
    Posts
    1,530
    Thanks
    48
    Thanked 173 Times in 133 Posts
    Congratulations
    1
    Congratulated 0 Times in 0 Posts
    McMillan makes several for the 788.

  8. #8
    Senior Member
    Join Date
    Jun 2011
    Location
    Dolores, Colorado
    Posts
    2,433
    Thanks
    107
    Thanked 350 Times in 271 Posts
    Congratulations
    1
    Congratulated 0 Times in 0 Posts
    Quote Originally Posted by Work2hunt View Post
    I did think of refinishing this stock and I still may. My wife was planning to use this gun and I thought I would try to get her something that she liked with a recoil pad on it vs the metal plate on the stock now.

    I did see Boy'ds had a decent selection among others but are these going to need a lot of fitting once purchased or should they require minor modifications if any?
    The inletting will need to be opened up a little. If you do buy a replacement, you will want to glass bed it. If you have a Dremel tool it will make the inletting job a lot easier. Lots of glass bedding inletting kits out there, just make sure you read the directions carefully, especially the part about the release agent.

    If you decide to refinish, this would be the time to install a recoil pad too.
    Colorado Cowboy
    Cowboy Action Shooter; Endowment Life Member-NRA
    The Original Rocket Scientist-Retired
    "My Father always considered a walk in the mountains as the equivalent of church going."
    Aldous Huxley

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •